At a request for zoom friendly tops that feel like sweatshirts, and have pockets, I experimented with the Leslie from 5 out of 4 patterns. The pattern is fabulous as is. My husband found this textured fleece in my stash and suggested our daughter would love it. A lighter weight fleece is a great way to start with this pattern due to the square neckline, corners and lots of layers. I skipped the zip for two reasons. 1. She is a fiddler. The last thing she needs to be doing is fiddling with the zipper on her collar during a work meeting, and 2. Despite the massive amount of zippers I have in my stash, there were none this color. Turns out that made things even more simple to put together. This is a great way to try out the pattern for fit and style before attempting a zipper. A confidence builder.
- Print and cut your size. Read through the tutorial that comes with the pattern. There are some really nice videos that are super helpful.
Cut out the following:
Front, back, sleeves, pocket, hood center back, and most critically, two mirror image side A hood pieces. The side B was designed to use the additional width that the zipper supplies to fit within the neckline. Don’t use that one for this project. Mark the center back neckline, and center back of the hood piece to help align them when sewing.
2. Sew the three piece hood together. Topstitch if you like, makes the inside a bit cleaner. Finish the edge with binding. I used fold over elastic.
3. Sew shoulder seams.
4. Prep the neckline. Staystitch the lower square neckline of the front piece. Use matching thread and with a shorter stitch length of 2, stitch from an inch above the inside corner of the neckline across the bottom and back up an inch. If you look closely, you can see my stay stitching on the wrong side of the front. It is sewn at a scant 1/4 inch seam allowance, so I do not have to remove it later.
5. Clip corners of the stay stitched neckline. Use your sharpest scissors to clip diagonally into the corners.
6. Pin the collar overlap. Baste the three lower edges together from pin to pin in the photo below at a scant 1/4 inch seam.
7. Attach the hood/collar to the body. Pin the right side of the lower edge of the hood/collar to the right side of the open neck edge. I pinned just outside the diagonal cuts. Double check to be sure you have the 1/4 inch of the hood/collar free on either edge, outside of the pin. With your work placed so that the hood collar is underneath, and the body is on top, we can begin sewing. the designer recommends basting this in place with a longer stitch. A stitch length of 3 is good, as it can be fairly easily removed, but will still hold and with this much loft you would want a longer stitch. Place the needle down at one corner, just inside the pin, and right on top of your stay stitching or basting stitches. Sew at this precise corner spot with a zero stitch length for a few stitches. Then stitch across the straight portion to the next corner, as pictured below. Stop precisely at the corner and make one or two stitches in place.
8. Stopped at the corner. Since I pinned just outside the corners. I could sew right up to my pin. Once I had made a few stitches in place, I removed the pin, and with the needle still firmly sunk into my fabric, I lifted the presser foot to pivot. There is a lot of excess fabric in the foreground of the below photo. We will deal with it in the next photos.
9 Sink that needle. All the way down.
10. Time to Twist and Shout! Needle still firmly sunk, lift your presser foot. Leave the bottom layers of the hood/collar as they are, arrange the top layers of the body of your sweatshirt, so that they are now swung around to the left and behind the presser foot. You can see a tiny bit of the staystitching in the photo below. Align the raw edges here, lower the presser foot, and stitch to the next spot where the notch in the hood/collar meets up with the shoulder seam. Next stop center backs, and after that the other shoulder seam and notch. You may want to switch to a stitch with more stretch to to around the sides and back of the neckline.
11. Almost there! In the photo below, we are getting back to where we started. You can see the initial stay stitches in the photo below. There will be excess fabric here just like there was at the first corner. Just manipulate it out of the way, so that you can minimize any puckering or tucks. When you get to that precise corner spot where you started, you can back tack or make a few stitches in place. Cut your threads and inspect your work! If you see puckers or tucks, now would be the time to correct them.
12. Neaten your stitches. The photo below is the inside of the neckline after serging around the sides and back only. It is optional. I left the straight part of the neckline without serging, because it was already pretty bulky with those layers. To tame the layers, you could stitch across that straight edge a second time.
13. Topstitch the neckline. This is optional. From the right side of the garment, I started at the back of the neck in the photo below. You can see the seams of my center hood on the left side of the photo, and a shoulder seam in the foreground. The seam is pressed towards the body and I am sewing just to the right of my seam, using the inside of my foot as a guide to keep my stitches even.
Close up of neckline finished and top stitched. I am happy with the outcome!
Add the pocket, sleeves, and finish the rest the sweatshirt. Now that you have conquered the zipless version, go forth and be the boss of the zipper! And then maybe the welt pockets.
This post contains affiliate links, which means I may receive a small commission from the pattern designer if you choose to purchase the pattern with this link. I certainly appreciate it if you do.
Here is my affiliate link. https://5outof4.com/product/leslie-top-tunic-and-dress/?affiliates=162
Wishing you happy sewing! Joan